[FE training-materials-updates] ttyUSB1 replaced by ttyUSB0
Michael Opdenacker
michael.opdenacker at free-electrons.com
Thu Oct 4 06:56:50 CEST 2012
Repository : git://git.free-electrons.com/training-materials.git
On branch : master
Link : http://git.free-electrons.com/training-materials/commit/?id=2416f07853b4c74739c948b6c001b0da084b15c8
>---------------------------------------------------------------
commit 2416f07853b4c74739c948b6c001b0da084b15c8
Author: Michael Opdenacker <michael.opdenacker at free-electrons.com>
Date: Thu Oct 4 05:23:39 2012 +0200
ttyUSB1 replaced by ttyUSB0
- We only see /dev/ttyUSB0 now
Only one port appears when plugging the Calao board
>---------------------------------------------------------------
2416f07853b4c74739c948b6c001b0da084b15c8
.../kernel-module-environment.tex | 11 ++++-------
.../kernel-serial-interrupt.tex | 4 ++--
labs/kernel-serial-output/kernel-serial-output.tex | 2 +-
3 files changed, 7 insertions(+), 10 deletions(-)
diff --git a/labs/kernel-module-environment/kernel-module-environment.tex b/labs/kernel-module-environment/kernel-module-environment.tex
index 11fbda5..02e01dc 100644
--- a/labs/kernel-module-environment/kernel-module-environment.tex
+++ b/labs/kernel-module-environment/kernel-module-environment.tex
@@ -118,11 +118,8 @@ errors disappear.
\section{Setting up serial communication with the board}
Plug the Calao board on your computer using its USB-A connector. When
-plugged-in, two serial ports should appear, \code{/dev/ttyUSB0} and
-\code{/dev/ttyUSB1}. \code{/dev/ttyUSB0} is used for the JTAG while
-\code{/dev/ttyUSB1} corresponds to the {\em DBGU}, the debugging
-serial port of the AT91 processor. You can also see this device appear
-by looking at the output of \code{dmesg}.
+plugged-in, a new serial ports should appear: \code{/dev/ttyUSB0}.
+You can also see this device appear by looking at the output of \code{dmesg}.
To communicate with the board through the serial port, install a serial communication program, such as \code{picocom}:
@@ -130,8 +127,8 @@ To communicate with the board through the serial port, install a serial communic
sudo apt-get install picocom
\end{verbatim}
-Run \code{picocom -b 115200 /dev/ttyUSB1}, to start a serial
-communication on \code{/dev/ttyUSB1}, with a baudrate of \code{115200}. If
+Run \code{picocom -b 115200 /dev/ttyUSB0}, to start a serial
+communication on \code{/dev/ttyUSB0}, with a baudrate of \code{115200}. If
you wish to exit \code{picocom}, press \code{[Ctrl][a]} followed by
\code{[Ctrl][x]}.
diff --git a/labs/kernel-serial-interrupt/kernel-serial-interrupt.tex b/labs/kernel-serial-interrupt/kernel-serial-interrupt.tex
index af997a7..2ebb2b1 100644
--- a/labs/kernel-serial-interrupt/kernel-serial-interrupt.tex
+++ b/labs/kernel-serial-interrupt/kernel-serial-interrupt.tex
@@ -73,7 +73,7 @@ message.
Compile and load your driver. Have a look at the kernel messages. You
should no longer be flooded with interrupt messages.
-Start \code{picocom} on \code{/dev/ttyUSB1}. Press one character (nothing will
+Start \code{picocom} on \code{/dev/ttyUSB0}. Press one character (nothing will
appear since the target system is not echoing back what we're
typing). Then, in the kernel log, you should see the message of our
interrupt handler. If not, check your code once again and ask your
@@ -96,7 +96,7 @@ character.
For each received character, print a message containing the character.
Compile and load your driver.
-From \code{picocom} on \code{/dev/ttyUSB1} on the host, send characters
+From \code{picocom} on \code{/dev/ttyUSB0} on the host, send characters
to the target. The kernel messages on the target should properly tell
you which characters are being received.
diff --git a/labs/kernel-serial-output/kernel-serial-output.tex b/labs/kernel-serial-output/kernel-serial-output.tex
index 358683c..78aa8f1 100644
--- a/labs/kernel-serial-output/kernel-serial-output.tex
+++ b/labs/kernel-serial-output/kernel-serial-output.tex
@@ -43,7 +43,7 @@ echo "test" > /dev/serial
\end{verbatim}
The \code{test} string should appear on the remote side (i.e in
-the \code{picocom} process connected to \code{/dev/ttyUSB1}).
+the \code{picocom} process connected to \code{/dev/ttyUSB0}).
You'll quickly discover than newlines do not work properly. To fix
this, when the userspace application sends \verb+"\n"+, you must send
More information about the training-materials-updates
mailing list